Just some of the setups we see

A 2.3 aerodyne cab and this bullbar would be amazing

Hello

I found a mistake in the sound.
If you install the engine Cummins ISX 15 600 and hear the horn or fanfare. The horn and fanfare sounds are wrong from the inside and outside views.
I made a video to hear what I mean.

https://www.youtube.com/watch?v=TFRZq0soE0A

How about fixing the non working guages

bubbdamadaussie wrote:How about fixing the non working gauges

Which gauges do not work?

get more options like bumpers and lights for on top of sleeper?

wish K200.
extra function button no lights on antenna and top lights on the cabin working.
now top lights on the cabin only working with top lights on antenna.

maybe this can me made on the roof that we can chance the rooflights : https://forum.scssoft.com/viewtopic.php?f=197&t=253435

[quote="Admin-RTA"[/quote]
Which gauges do not work?[/quote]
Привет Админ. не работают датчики давления воздуха.

Further info on the gauges not working:

- Screenshot of K200 v14.2 for ATS while engine is started.

Voltmeter - Not working
Enigine oil pressure - Not working
Pyrometer - Currently indicating the main air pressure but in psi, not bar. Seen that there is no pyro data in this game I would like this big gauge to be the turbo gauge. ??? (only a suggestion)
Engine water temp - Not working
Fuel level - Working
Turbo boost - Working partially. Gauge face is kPa but needle is psi or bar.
Rear/Front Air: Not woking. These 2 gauges can be used to show the air pressure instead of the big gauge in the middle.

The animations are working fine but the units (psi,bar,kPa) are wrong.

Added after 14 minutes 58 seconds:
Suggestion:

-Add animation to diff lock switches.

the fifth wheel a little bit more to the back of the truck , have with some trailers turning problems .
example this pack : https://www.modland.net/euro-truck-simulator-2/trailers/tsa-trailer-pack-v-1.0.html

Added after 9 minutes 35 seconds:
For ATS and ETS2 .
or is it easy to make a tempory file? that becomes above the mods in mod manager.

Could anyone confirm if this is happening to them? For me the GPS is very bright so you can't make out the detail very well (like the speed limit sign) and I can't read it.

I've tried changing all my graphics settings including scaling but nothing seems to be able to change it, it's like the one in the K200 it overly bright.

This is what I currently see:
ets2_20181218_232329_00 by Tom TruckSim, on Flickr

Here is what I thought was the same GPS from SCS in the DAF, which is easier to read:
ets2_20181218_234005_00 by Tom TruckSim, on Flickr

Hi Tommo,
I tried the Screen-Corner GPS in my K200, in addition to the SISL GPS that I usually use, and it does look a bit brighter compared to the dash-mount GPS in the SISL Mega Pack. The white centre of the speed limit does look a bit "bloomy" and the background more like dark grey than black by comparison, it's a bit more obvious when you click to enlarge the screenshot below. It looks almost like it's using a different target gamma?

This is with in-game brightness at about 35%, but as you found, it doesn't seem to make any difference when changing graphics settings.

It does look slightly more noticeable in the screenshot than it does in game, as I have HDR active but am running the Filmic Lighting mod to compensate for the HDR Bloom and I don't think this is picked up in the screenshots.

(On a side-note, did you get my PM last week?)
Cheers
Ian

Hi Ian,

Thank you for that, I was using a different HDR enabled mod which seems to be the issue as it keeps a small amount of bloom in the game which the gps seemed to latch onto. I've tried it with the filmic lighting one you've suggested and it looks much better and more importantly is nicely readable so thank you for that.

Tommo

Could you do a more aussie style bullbar like this http://www.barupbullbars.com.au/bullbars/kenworth/kenworth-k200#
http://www.barupbullbars.com.au/bullbars/kenworth/kenworth-k200#
Could you also do a flat roof http://www.barupbullbars.com.au/bullbars/kenworth/kenworth-k200#

is it possible to have beacons on the roof and NO lights on the antenna tip.
I`ll drive with camera position 4 on the keyboard and then the antenna lights are a shining problem.

Yep - an aussie bullbar is a must for any aussie truck please.

bionicbunnybones wrote:Could you do a more aussie style bullbar like this

Depending on which bumper you choose for the K200, there are choices for bullbars.
The bullbar that comes with the K200 is almost identical to those in the pictures you linked to.

Thanks room217au. I figured there had to be one somewhere.